gpio-config

1 · Platform Detection

Explicit Detection

Model/Variant Detection

RPi Variants:

ESP32 Variants:

ESP32 Modules:

Ambiguity Rules

1. •If platform cannot be determined from context: ask the user. NEVER silently default to a platform.
2. •If platform is detected but variant is unknown: ask the user for model/variant. Default to most conservative variant if user declines (rpi3 for RPi, esp32 + WROOM for ESP32).
3. •Unsupported platforms (RP2040/Pico, STM32, Arduino AVR, BeagleBone): state that the platform is not yet supported, list supported platforms, offer to help if user switches.

2 · Reference Loading

ALWAYS load the platform pin database. Load other files only when their trigger condition is met.

3 · Core Workflow

Step 1 — Parse

Extract from the user's request:

• •Target platform and variant (or flag as unknown)
• •Required protocols and their quantities (e.g., "2× I2C", "1× SPI")
• •Named devices/modules (e.g., "BME280", "SSD1306", "NeoPixel")
• •Existing pin commitments ("I'm already using GPIO17 for...")
• •Special requirements (deep sleep wake, interrupt-capable, analog input, high-speed)
• •Framework preference (gpiozero, RPi.GPIO, Arduino, ESP-IDF) or "not specified"

Step 2 — Detect

Apply Section 1 rules. Result: confirmed platform + variant + module type, OR ask the user.

Step 3 — Load

Apply Section 2 table. Load all triggered reference files before proceeding.

Step 4 — Gather

If any critical information is missing (platform, protocol count, or device identity), ask ONE concise follow-up question covering all gaps. If information is merely ambiguous but reasonable defaults exist, proceed and list assumptions in the output. Never ask more than one follow-up message.

Step 5 — Generate

Assign pins using platform-specific strategy:

RPi strategy:

1. •Assign hardware-native pins first (I2C → GPIO2/3, SPI0 → GPIO7–11, UART → GPIO14/15)
2. •Prefer GPIO12/13 for hardware PWM
3. •Never assign GPIO0 or GPIO1 (I2C EEPROM reserved)
4. •Use clean GPIOs for general digital I/O: 5, 6, 16, 17, 22, 23, 24, 25, 26, 27
5. •Note all pins that pull high/low at boot
6. •Track cumulative current draw against 50mA GPIO budget

ESP32 strategy:

1. •Never assign flash SPI pins (GPIO6–11; also GPIO16–17 on WROVER)
2. •Warn if assigning strapping pins (GPIO0, 2, 5, 12, 15) — add boot-state note for each
3. •Elevate GPIO12 (MTDI) to a stronger warning: wrong state at boot can set flash voltage to 1.8V and brick the module
4. •Use conventional I2C pins (GPIO21 SDA, GPIO22 SCL) unless conflict exists
5. •Use native SPI pins: VSPI (GPIO5/18/19/23) or HSPI (GPIO12/13/14/15) — note strapping overlap on HSPI
6. •If WiFi is enabled, avoid ADC2 channels entirely (esp32 variant only)
7. •Assign input-only pins (GPIO34–39) only for inputs, never outputs or bidirectional
8. •Prefer RTC-capable GPIOs for deep-sleep wake sources
9. •Reserve GPIO1/3 (UART0 TX/RX) for debug serial unless user explicitly reassigns
10. •Note that any output-capable GPIO supports PWM via LEDC — no dedicated PWM pins needed

Step 6 — Validate

Invoke the validation script:

python scripts/validate_pinmap.py --format json <<'EOF'
<input JSON>
EOF

If validation returns errors: reassign conflicting pins and re-validate. Loop a maximum of 3 times. If still failing after 3 attempts, present the best result with remaining warnings explained.

If validation returns warnings only: include warnings in output, proceed.

Step 7 — Output

Generate the response using Section 4 format. Then invoke the generation script:

python scripts/generate_config.py --format json --framework <framework> <<'EOF'
<input JSON>
EOF

Include all script outputs in the structured response.

4 · Output Format

Pin Assignment Table

• •RPi columns: Function | GPIO (BCM) | Physical Pin | Alt Mode | Notes
• •ESP32 columns: Function | GPIO | Notes | Strapping? | RTC Channel?
• •Sort by function group (I2C, SPI, UART, PWM, digital I/O, analog)

Configuration

• •RPi: config.txt lines (dtoverlay, dtparam, gpio= directives). Note correct path for variant.
• •ESP32: menuconfig/sdkconfig.defaults lines (if Arduino: note that most config is in code)

Initialization Code

• •RPi: provide both gpiozero and RPi.GPIO versions unless user specified one
• •ESP32: provide both Arduino and ESP-IDF versions unless user specified one
• •Always include: pin mode setup, pull-up/pull-down config, protocol init with correct pins, brief comments

Wiring Notes

• •Human-readable wiring instructions using physical pin numbers AND GPIO numbers
• •Include: pull-up resistor values for I2C/1-Wire, power rail connections, level shifter notes if mixing voltages, decoupling caps for sensitive devices

Warnings

• •Pin conflicts detected during validation
• •Strapping pin usage (ESP32)
• •Current budget concerns
• •UART/Bluetooth conflicts (RPi 3/4/Zero2W)
• •PWM/audio conflicts (RPi)
• •ADC2/WiFi conflicts (ESP32)
• •Deprecated library warnings (e.g., RPi.GPIO on Pi 5)

Alternatives

• •For every conflict that was auto-resolved, explain: original pin → replacement pin and why
• •If multiple valid assignments exist, briefly note the top alternative

5 · Critical Rules

Universal

1. •Always present GPIO numbers prominently — never reference physical pin numbers only
2. •Never silently assign a reserved or restricted pin — always warn
3. •Check I2C device address collisions when multiple I2C devices share a bus
4. •Include pull-up/pull-down notes for every protocol that requires them
5. •Respect per-platform current limits and warn when cumulative draw approaches budget
6. •Warn about deprecated libraries (RPi.GPIO on Pi 5 has limited support; suggest gpiozero or lgpio)
7. •If the user's request exceeds available pins, say so and suggest multiplexing (I2C expander, SPI daisy-chain)

RPi-Specific

1. •Use BCM numbering by default. If user requests BOARD numbering, provide both.
2. •Never assign GPIO0 or GPIO1 — reserved for HAT EEPROM I2C
3. •On Pi 3/4/Zero 2W: UART0 (GPIO14/15) is linked to Bluetooth by default. Warn and explain dtoverlay=miniuart-bt or dtoverlay=disable-bt
4. •Prefer GPIO12/13 for hardware PWM (PWM0/PWM1). GPIO18 is PWM-capable but conflicts with PCM/audio.
5. •PWM on GPIO18 + audio output = conflict. Warn if both are needed.
6. •Total GPIO current budget: 50mA across all pins. Track and warn.
7. •SPI0 claims GPIO7–11 (CE1, CE0, MISO, MOSI, SCLK). Do not assign these for other use when SPI0 is active.
8. •Config.txt path: /boot/config.txt on Pi 3 and older, /boot/firmware/config.txt on Pi 4/5 with Bookworm+

ESP32-Specific

1. •Flash SPI pins (GPIO6–11) are never available. On WROVER modules, GPIO16–17 are also reserved (PSRAM).
2. •Strapping pins (GPIO0, 2, 5, 12, 15): warn on every use with the required boot state for each.
3. •GPIO12 (MTDI) gets an elevated warning: if pulled high at boot, flash voltage switches to 1.8V — can brick 3.3V flash modules. Advise efuse or boot-fix if user must use it.
4. •ADC2 (GPIO0, 2, 4, 12–15, 25–27) is unavailable when WiFi is active — this applies to the original ESP32 variant only, not S2/S3/C3/C6.
5. •GPIO34–39 are input-only: no internal pull-ups, no output mode. Assign only for input signals.
6. •For deep-sleep wake: use RTC GPIOs only (GPIO0–21, 25–27 on ESP32). Check per-variant RTC GPIO list.
7. •UART0 (GPIO1 TX, GPIO3 RX) is the default debug/programming port. Do not reassign without explicit user intent.
8. •Any output-capable GPIO can generate PWM via LEDC peripheral — no special pin selection needed.
9. •Maximum source current per pin: 40mA (recommended 20mA). Total chip limit varies by variant.

6 · Script Interface

validate_pinmap.py

Location: scripts/validate_pinmap.py

CLI usage:

python scripts/validate_pinmap.py --format json [--verbose] < input.json
python scripts/validate_pinmap.py --help

Input JSON schema:

{
  "platform": "rpi | esp32",
  "variant": "rpi3 | rpi4 | rpi5 | rpi_zero2w | esp32 | esp32s2 | esp32s3 | esp32c3 | esp32c6",
  "module": "WROOM | WROVER | null",
  "wifi_enabled": true,
  "pins": [
    {
      "gpio": 17,
      "function": "I2C_SDA | I2C_SCL | SPI_MOSI | SPI_MISO | SPI_SCLK | SPI_CS | UART_TX | UART_RX | PWM | DIGITAL_IN | DIGITAL_OUT | ANALOG_IN | 1WIRE | CAN_TX | CAN_RX",
      "protocol_bus": 0,
      "device": "BME280",
      "pull": "up | down | none",
      "notes": ""
    }
  ]
}

Output JSON schema:

{
  "valid": true,
  "errors": [
    {
      "gpio": 6,
      "code": "RESERVED_PIN | CONFLICT | INPUT_ONLY_AS_OUTPUT | STRAPPING_UNACKNOWLEDGED | ADC2_WIFI | CURRENT_EXCEEDED",
      "message": "Human-readable error",
      "severity": "error"
    }
  ],
  "warnings": [
    {
      "gpio": 12,
      "code": "STRAPPING_PIN | UART_BT_CONFLICT | PWM_AUDIO_CONFLICT | DEPRECATED_LIB | CURRENT_WARNING | BOOT_STATE",
      "message": "Human-readable warning",
      "severity": "warning"
    }
  ],
  "summary": {
    "total_pins": 8,
    "errors": 0,
    "warnings": 2,
    "current_draw_ma": 32
  }
}

Exit codes: 0 = valid (warnings ok), 1 = errors found, 2 = invalid input

generate_config.py

Location: scripts/generate_config.py

CLI usage:

python scripts/generate_config.py --format json --framework arduino|espidf|gpiozero|rpigpio [--verbose] < input.json
python scripts/generate_config.py --help

Input JSON schema: same as validate_pinmap.py input, plus:

{
  "platform": "rpi | esp32",
  "variant": "rpi3 | rpi4 | rpi5 | rpi_zero2w | esp32 | esp32s2 | esp32s3 | esp32c3 | esp32c6",
  "module": "WROOM | WROVER | null",
  "wifi_enabled": true,
  "pins": [],
  "framework": "arduino | espidf | gpiozero | rpigpio"
}

Output JSON schema:

{
  "config_lines": ["dtoverlay=i2c1", "dtparam=spi=on"],
  "init_code": "# Full initialization code as a single string with newlines",
  "wiring_notes": [
    "Connect BME280 SDA to GPIO2 (physical pin 3). Add 4.7kΩ pull-up to 3.3V."
  ],
  "warnings": ["GPIO12 is a strapping pin — see boot state notes"],
  "alternatives": [
    {
      "original_gpio": 12,
      "alternative_gpio": 17,
      "reason": "Avoids MTDI strapping pin risk"
    }
  ]
}

Exit codes: 0 = success, 1 = generation error, 2 = invalid input

7 · Requirements

• •Python 3.9+ (standard library only — no pip packages required)

8 · Example

User request: "Set up a weather station with BME280 temperature sensor and SSD1306 OLED display on Raspberry Pi 4"

Generated pinmap (excerpt):

{
  "platform": "rpi",
  "variant": "rpi4",
  "pins": [
    {"gpio": 2, "function": "I2C_SDA", "protocol_bus": 1, "device": "BME280+SSD1306", "pull": "external_up"},
    {"gpio": 3, "function": "I2C_SCL", "protocol_bus": 1, "device": "BME280+SSD1306", "pull": "external_up"},
    {"gpio": 17, "function": "DIGITAL_OUT", "device": "Status LED", "pull": "none"}
  ]
}

Generated initialization code (gpiozero, excerpt):

from gpiozero import LED
import smbus2

bus = smbus2.SMBus(1)  # I2C bus 1: SDA=GPIO2, SCL=GPIO3
# BME280 at 0x76, SSD1306 at 0x3C — shared I2C bus, no conflict

status_led = LED(17)